PIC Mapping for : [12.07.2006] for wiring details, refer to schematics on the website. Midi channels: 5 and 6 (offset 0) PIC1: On MidiHub board - motor control (0-10V output) PWM - midi ctrl 7 ( both channels) - X17-2 - pic pin 13 - dim lights control (PWM output) - midi ctrl 8 ( both channels) - X17-3 - pic pin 12 - motor on /off switch - midi ctrl 66 (both channels ) - X11-2 - pic pin 21 'was 5 - lites on /off switch - note 120 (on/off) - X11-3 - pic pin 4 (indien deze pin ook voor AN nodig is, kan hiervoor ook pin 16 gebruikt worden) Stepper motor hardware connections: - low motor power down X12-2 - midi ctrl 67 pic pin 3 (indien deze pin ook voor AN nodig is, kan hiervoor ook pin 15 gebruikt worden) - high motor power down X12-3 - midi ctrl 68 pic pin 2 - low motor cw pulses X15-2 pic pin 25 - low motor cww pulses X15-3 pic pin 24 - high motor cw pulses X16-1 pic pin 23 - high motor cww pulses X16-2 pic pin 22 - X16-3 GND for sensor boards - X16-4 +5V dc for sensor boards - low motor sensor - analog input X16-5 pic pin 5 : AN3 - high motor sensor - analog input X16-6 pic pin 7 : AN4 required: - low windvalve tremolo midi ctrl 11, both channels the data byte should control the tremolo speed (rotational speed) reception of this command resets all other commands for this motor if the speed parameter is zero, the valve should stop turning and go back to the full opened position - high windvalve tremolo midi ctrl 12, both channels the data byte should control the tremolo speed (rotational speed) reception of this command resets all other commands for this motor if the speed parameter is zero, the valve should stop turning and go back to the full opened position - low windvalve position evt. channel aftertouch via low channel (5) channel pressure: 208 + 5, position-byte: 0= closed, 127 = opened (90 degrees) reception of this command resets all other commands for this motor - high windvalve position evt. channel aftertouch via high channel (6) Channel pressure: 208 + 6, position-byte: 0= closed, 127 = opened (90 degrees) reception of this command resets all other commands for this motor should also work on reception of controller 1 and 2, as received on both channels controller 1: low windvalve, position-byte: 0= closed, 127 = opened (90 degrees) controller 2: high windvalve, position-byte: 0= closed, 127 = opened (90 degrees) reception of these controlllers reset all other commands for the respective motors ****************************************************************************** Note+ Velo PIC boards: PIC- series normal notes 36 - 108: note + velo, midi channel 5 PIC- series quartertones 36 - 108: id , midi channel 6 optional: polyphonic aftertouch in PWM of hold-signal. (4 bits is enough) Controller 69: polyphonic aftertouch on or off (switch, working on either channel) PIC 1,3,5,7,9,11 : Kanaal 5, boards K1-K6 PIC 2,4,6,8,10,12: kanaal 6, boards Q1-Q6 PIC 1,2 : uitgangen 1-14 = notes 34 - 47 PIC 3 : uitgangen 1-14 = notes 48 - 61 PIC 4 : uitgangen 14-1 = notes 48 - 61 PIC 5 : uitgangen 1-14 = notes 62 - 75 PIC 6 : uitgangen 14-1 = notes 62 - 75 PIC 7 : uitgangen 1-14 = notes 76 - 89 PIC 8 : uitgangen 14-1 = notes 76 - 89 PIC 9 : uitgangen 1-14 = notes 90 - 103 PIC 10 : uitgangen 14-1 = notes 90 - 103 PIC 11 : uitgangen 1-14 = notes 104 - 117 PIC 12 : uitgangen 14-1 = notes 104 - 117